ARCHSPLACE
Architecture, made simple — since 2018
Rotate

PlanQin the studio

Rotate

Rotate turns elements of the plan about a center you click, by the angle between a reference point and a third point, or by degrees you type. Held with Ctrl it turns a copy and keeps the original.

What it is

Rotate turns what you hold about a center. It takes four clicks, the same as in the 3D view: the element (or the selection you already hold), the center, a reference point that says where the turn starts, and the point that says where it ends. The angle between the reference and the last point is the turn. You can also type the angle in degrees once the center is set.

Walls, pipes and beams turn as a network: the corners they share with walls that are not selected follow them, and a wall that ends on the face of a turned wall stays on it. Columns and fixtures turn their own orientation with them. Held with Ctrl, Rotate turns a copy and leaves the original where it was.

When to use it

  • Setting a wing of the plan at an angle to the rest.
  • Turning a fixture or a column to face the right way.
  • Laying copies around a center, such as columns on a circle, with one copy and a typed count.

The steps

  1. Take the tool. Press Q, or click the Rotate button. If you already hold a selection, it is what turns.

    Rotate armed: the hand rests on the Rotate button, third in the toolbar, its name Rotate (Q) under it, and the status bar lists the four clicks: element, center, reference, angle.
  2. Click the element. Click the element that turns; with several elements selected, a click on any of them turns them all. If you already hold a selection, a first click on empty ground skips this step and is taken as the center.

    The hand on the partition that runs north from the middle of the square: the status bar names the line under the pointer, and a click there takes the partition as what turns.
  3. Click the center. The magnet holds the click on the nearest corner, middle or crossing within reach, so the turn pivots exactly there.

    The center clicked on the partition's south end: a dashed line runs from it to the hand, with no ghost yet.
  4. Click the reference. Click a point that names where the turn starts, often an end of the element itself. From there, a ghost of the turned elements follows the cursor.

    The reference clicked on the partition's north end and the hand moved out to the west: a ghost of the partition stands turned, its angle, 45.0 degrees, read beside the hand.
  5. Click the angle, or type it. Move the cursor until the ghost stands where you want and click. Shift holds the angle to steps of 15 degrees, and F8, while it is on, to steps of 90 degrees. Or type the angle in degrees and press Enter: the elements turn by that many degrees, counterclockwise for a positive number. Hold Ctrl (⌘ on a Mac) as you click or press Enter to turn a copy.

    The hand brought to the horizontal: the ghost lies due west of the center and the angle reads 90.0 degrees.
  6. Go on round. Right after a turned copy, type x and a number, then Enter, to repeat the same turn about the same center until there are that many copies.

    A copy turned 90 degrees, then x3 and Enter: partitions with their doors radiate from the center to the west, south and east, and the square stands in four rooms with no finding in the status bar.

What it refuses

  • A hosted element alone. A window, a door or a device on a wall rides its wall. Turned alone, it stays as it was and a message says to rotate the wall instead.
  • A component turned inside out. A component instance turns, but never changes its size or its handedness.
  • A turn that would break a joint. A turn that would leave a wall, a pipe or a beam shorter than a centimeter writes nothing and says why.
  • Annotations. A dimension, a detail or a callout frame does not turn with Rotate.

What it writes to the contract

One step, which one undo takes back. Every turned element gets its new points: a wall's two ends, a column's position and its angle, a fixture's position and its angle, a stair's walk line, a roof's corners. The ends of walls, pipes and beams joined to them are written too. A copy adds new entries at the end of their lists instead of changing the originals.

Concepts

Common questions

How do I rotate by an exact angle?

Select the elements, press Q, click the center, then type the angle in degrees and press Enter. A positive angle turns counterclockwise.

Can I rotate a single window or a socket?

No. A window, a door or a wall device rides its wall: the studio says so and leaves it as it is. Rotate the wall instead, and what it hosts turns with it.

How do I copy elements around a center?

Rotate them once with Ctrl held, then type x and the total count, such as x6, and press Enter: the same turn is repeated around the same center.