ARCHSPLACE
Architecture, made simple — since 2018
Circle in the tile editor

SketchCin the studio

Circle in the tile editor

Circle draws a round joint inside a pattern's tile from its center and a point on it, or from its center and a typed radius. The circle is one joint, and it must stand whole inside the tile.

What it is

Circle draws a round joint inside the tile: a dot in a terrazzo, a ring in a medallion, the circle of a decorative tile. You give it its center, then its size. The tile's corners, the middles of its sides, its centre and its edges are magnets, and so are the ends, the middles and the length of the joints already drawn.

A circle is one joint. It is selected, nudged, erased and undone whole. Once drawn, its center and the points at its left, right, top and bottom become magnets for the next joints.

When to use it

  • To draw a round motif inside the tile.
  • When you know a circle's center and its radius.
  • When you know two points of its diameter, or three points on it, use Circle by 2 points or Circle by 3 points instead.

The steps

  1. Take the tool. Press C, or click Circle on the bar. It shares its button with Circle by 2 points, Circle by 3 points and Polygon. The hint at the pointer asks for the center of the circle.

    Circle armed on the bar: a square tile eight inches on a side, dashed, in the middle of the pane with the repeat dimmed around it, and the hint beside the hand asking for the center of the circle.
  2. Place the center. Click inside the tile, or type x;y and press Enter, measured from the tile's lower-left corner.

    The center placed on the tile's middle: a dashed ghost circle follows the hand with its radius drawn from the center, and the hint shows the radius and says to click a point of the circle or type the radius.
  3. Give the size. A ghost circle follows the pointer, with its radius drawn and shown in the hint. Click a point of the circle, or type the radius and press Enter. You can also press on the center and drag, releasing on the circle. If the ghost turns red, the click would be refused.

    The radius typed: the ghost circle holds its size and the hint carries the typed 2.4 inches after the invitation to press Enter.
  4. Draw the next one. The circle stands and the tool waits for a new center.

    A second circle dragged from the same center and released on the circle: two concentric circles stand in the tile and repeat in every tile around it.
  5. Step back or change your mind. Escape clears what you typed, then drops the center. Ctrl+Z undoes the last circle.

    A center dropped with Escape and the last circle undone with Ctrl+Z: one circle is left in the tile, repeated around it, and the hint asks for the center of a new one.
  6. Hand the tile back. Press Done on the bar at the foot, or Enter with nothing in hand. Escape with nothing in hand and nothing selected closes the editor without writing anything.

    Done pressed: the editor has closed to the plan, a notice says the tile is saved and no surface places it yet, and the new pattern's row stands in the Standard panel under the hand.

What it refuses

  • A circle that leaves the tile. If any part of it would stand outside the tile, nothing is drawn and the editor says a shape must stay inside the module. Your center stays in hand.
  • A circle too small. A radius under a millimetre, or a second click on the center, is refused with a joint under 1 mm is refused.
  • Cutting the circle at the edge. A circle is never cut to fit: it is kept whole or refused whole. The same holds later: if you make the tile smaller with Scale the drawing off, a circle that no longer fits is dropped, and the editor counts it.

What it writes to the contract

Nothing while you draw: the circle stays in the tile editor, where Ctrl+Z takes it back. When you press Done, the whole tile is written to the project's patterns in one step you can undo. A circle is stored as one closed joint made of two half circles, in metres from the tile's lower-left corner. A standard pattern is never changed: Done saves the project's own version of it under the same name, and every surface that lays it follows. Save as new writes a new pattern instead. Cancel writes nothing.

Common questions

How do I draw a circle of an exact size?

Click the center, type the radius and press Enter. The radius is in the project's units.

Why was my circle refused?

The whole circle must stand inside the tile. If any part of it would cross the tile's edge, nothing is drawn, and your center stays in hand so you can try a smaller radius.

Can I select half of a circle?

No. A circle is one joint: it is selected, moved and erased whole. To keep part of it, cut it with Trim or Break, which leaves an arc.